DHCPv6 は内部 DHCP サーバではサポートされません。
オペレーティング システムは、DHCP リレーをサポートする業界標準の外部 DHCP サーバを使用することにより、ネットワークに対しては DHCP リレーとして機能し、クライアントに対しては DHCP サーバとして機能するように設計されています。これは、各 switch controller device は、DHCP サーバに対しては DHCP リレー エージェントとして機能し、無線クライアントに対しては仮想 IP アドレスでの DHCP サーバとして機能することを意味します。
switch controller device は DHCP サーバから取得したクライアント IP アドレスをキャプチャするため、 switch controller device 内、 switch controller device 間、およびサブネット間でのクライアント ローミング時に、各クライアントに対して同じ IP アドレスが保持されます。
外部 DHCP サーバは DHCPv6 をサポートします。 |
DHCP はインターフェイスごとに、または WLAN ごとに設定できます。 特定のインターフェイスに割り当てられたプライマリ DHCP サーバのアドレスを使用することをお勧めします。
個々のインターフェイスに DHCP サーバを割り当てることができます。 プライマリおよびセカンダリ DHCP サーバの管理インターフェイス、AP マネージャ インターフェイス、動的インターフェイスの設定、DHCP サーバをイネーブルまたはディセーブルするためのサービス ポート インターフェイスの設定を行うことができます。 WLAN で DHCP サーバを定義することもできます。 この場合、サーバは、WLAN に割り当てられたインターフェイスの DHCP サーバ アドレスを上書きします。
高度なセキュリティが必要な場合は、すべてのクライアントが DHCP サーバから IP アドレスを取得するように設定してください。 この要件を適用するために、DHCP アドレスですべての WLAN を設定できます。 Assignment Required 設定で設定して、クライアントの固定 IP アドレスが禁止されるようにします。 DHCP Addr. Assignment Required が選択されている場合、クライアントは DHCP を使って IP アドレスを取得する必要があります。 固定 IP アドレスを持つクライアントはすべて、ネットワーク上で許可されなくなります。 クライアントの DHCP プロキシとして動作する switch controller device が、DHCP トラフィックを監視します。
セキュリティが多少劣ってもかまわない場合は、DHCP Addr. Assignment Required を無効に設定して WLAN を作成できます。 その後クライアントは、固定 IP アドレスを使用するか、指定された DHCP サーバの IP アドレスを取得するかを選択できます。
DHCP アドレス 有線ゲスト LAN に対する Assignment Required は、サポートされていません。 |
個別の WLAN は、 [DHCP アドレス割り当て必須(DHCP Address Assignment Required)] を無効にして作成できます。 これは、 switch controller device の DHCP プロキシがイネーブルの場合だけです。 DHCP プロキシをディセーブルにする必要があるプライマリ/セカンダリ コンフィギュレーションの DHCP サーバを定義しないでください。 このような WLAN では、すべての DHCP 要求がドロップするため、クライアントは固定 IP アドレスを使用しなければなりません。 これらの WLAN は、無線接続による管理をサポートしていません。
内部 DHCP サーバを使用する場合は、コントローラの管理インターフェイスの IP アドレスを DHCP サーバの IP アドレスとして設定する必要があります。
[WLANs] を選択して、[WLANs] ページを開きます。 | ||
インターフェイスを割り当てる WLAN の ID 番号をクリックします。 [WLANs > Edit (General)] ページが表示されます。 | ||
[General] タブの [Status] チェックボックスをオフにし、[Apply] をクリックして WLAN を無効にします。 | ||
WLAN の ID 番号を再度クリックします。 | ||
[General] タブの [Interface] ドロップダウン リストから、この WLAN で使用するプライマリ DHCP サーバを設定したインターフェイスを選択します。 | ||
[Advanced] タブを選択して、[WLANs > Edit]([Advanced])ページを開きます。 | ||
WLAN 上で、WLAN に割り当てられたインターフェイスの DHCP サーバ アドレスを上書きする DHCP サーバを定義する場合、[DHCP Server Override] チェックボックスをオンにして、[DHCP Server IP Addr] テキスト ボックスに目的の DHCP サーバの IP アドレスを入力します。 チェックボックスはデフォルトでは、無効になっています。 | DHCP の設定には、DHCP サーバのオーバーライドではなく、特定のインターフェイスに割り当てられたプライマリの DHCP アドレスを使用する方式が優先されます。 |
DHCP サーバのオーバーライドはデフォルト グループにのみ適用できます。 |
WLAN で DHCP サーバのオーバーライドが有効になっており、コントローラの DHCP プロキシが有効になっている場合、WLAN にマッピングされるインターフェイスが DHCP サーバの IP アドレスを持っているか、または WLAN に DHCP サーバの IP アドレスを設定する必要があります。 |
DHCP アドレス 有線ゲスト LAN に対する Assignment Required は、サポートされていません。 |
PMIPv6 は DHCP ベースのクライアントだけをサポートし、固定 IP アドレスはサポートしていません。 |
次のコマンドを入力して、WLAN を無効にします。 config wlan disable wlan-id | ||
この WLAN で使用するプライマリ DHCP サーバを設定したインターフェイスを指定するには、次のコマンドを入力します。 config wlan interface wlan-id interface_name | ||
WLAN 上で、WLAN に割り当てられたインターフェイスの DHCP サーバ アドレスを上書きする DHCP サーバを定義するには、次のコマンドを入力します。 config wlan dhcp_server wlan-id dhcp_server_ip_address | DHCP の設定には、DHCP サーバのオーバーライドではなく、特定のインターフェイスに割り当てられたプライマリの DHCP アドレスを使用する方式が優先されます。 オーバーライド機能を有効にした場合、 show wlan コマンドを使用して DHCP サーバが WLAN に割り当てられていることを確認できます。 |
WLAN で DHCP サーバのオーバーライドが有効になっており、コントローラの DHCP プロキシが有効になっている場合、WLAN にマッピングされるインターフェイスが DHCP サーバの IP アドレスを持っているか、または WLAN に DHCP サーバの IP アドレスを設定する必要があります。 |
config wlan enable wlan-id
DHCP をデバッグするには、次のコマンドを使用します。
debug dhcp packet { enable | disable } :DHCP パケットのデバッグを有効または無効にします。
debug dhcp message { enable | disable } :DHCP エラー メッセージのデバッグを有効または無効にします。
debug dhcp service-port { enable | disable } :サービス ポート上の DHCP パケットのデバッグを有効または無効にします。
IMAGES
VIDEO
COMMENTS
Cisco Wireless LAN Controller Configuration Guide, Release 7.4 . Chapter Title. ... you can configure all WLANs with a DHCP Addr. Assignment Required setting, which disallows client static IP addresses. If DHCP Addr. Assignment Required is selected, clients must obtain an IP address via DHCP. ... config wlan dhcp_server wlan-id dhcp_server_ip ...
If you want to define a DHCP server on the WLAN that will override the DHCP server address on the interface assigned to the WLAN, enter this command: config wlan dhcp_server wlan-id dhcp_server_ip_address [ required] The required is an optional argument. Using this argument forces DHCP address assignment to be applied to the WLAN.
(Cisco Controller) >config wlan dhcp_server 1 0.0.0.0 required 1 Note: DHCP server override is applicable only to the default AP group. (Cisco Controller) > To be clear, I don't care about a DHCP server override (that's the checkbox up to the top of "DHCP Addr. Assignment") - see screenshot below.
Assignment Required is selected, clients must obtain an IP address via DHCP. Any client with a static IP address is not allowed on the network. The DHCP Required option in WLAN settings allows you to force clients to do a DHCP address. request/renew every time they associate to the WLAN before they are allowed to send or receive other.
--> The DHCP Required option forces the wireless user to send a DHCP address request/renew messages every time they associate to the WLAN before they are allowed to send or receive other traffic to the network.--> This feature may have some problems in some client implementations which do not do a DHCP renew until the lease time expires.
Device(config-wireless-policy)# ipv4 dhcp opt82 rid: Supports the addition of Cisco 2-byte Remote ID (RID) for DHCP Option 82. Step 23. ipv4 dhcp server ip-address. Example: Device(config-wireless-policy)# ipv4 dhcp server 10.10.10.1: Configures the WLAN's IPv4 DHCP server. Step 24. vlan vlan-name. Example: Device(config-wireless-policy)# vlan 32
WLAN DHCP override works only if DHCP service is enabled on the controller. You can configure DHCP service in either of the following ways: Configuring the DHCP pool on the controller. Configuring a DHCP relay agent on the SVI. Note that the VLAN of the SVI must be mapped to the WLAN where DHCP override is configured.
The WLC will not move you back to DHCP_Required. The client may choose to reach out through DHCP again, but we do not require that they do. -Eric N. Cisco Wireless TAC. Selected as BestSelected as Best LikeLikedUnlike. All Answers. vinodhk2. 11 years ago. DHCP request / renew for each roam is not a necessity.
config interface port management physical-ds-port-number (for all controllers except the 5508 WLC) . config interface dhcp management ip-address-of-primary-dhcp-server [ip-address-of-secondary-dhcp-server] . config ipv6 interface acl management access-control-list-name
Client Timers. Same as with security recommendation, it is advisable to use client exclusion for ISE. Exclusion should be enabled, normally with exclusion set to 180 seconds. (Cisco Controller) >config wlan exclusionlist <wlan-id> enabled. (Cisco Controller) >config wlan exclusionlist <wlan-id> 180.
This procedure explains how to configure the users in the RADIUS server and the RADIUS (IETF) attributes used to assign VLAN IDs to these users. Complete these steps: From the ACS GUI, click User Setup. In the User Setup window, enter a username in the User field and click Add/Edit.
By default, DHCP option 82 is enabled for all clients. You can control the wireless client behavior using the WLAN suboptions. The Cisco converged access platforms support internal DHCP server functionality. However, as a general deployment guideline to build large enterprise-class networks, we recommend that you use external DHCP server to ...
DHCP seems to work fine for the clients with roaming after disabling "DHCP Addr. Assignment", but now I lose the ability to see the hostname of some iPhone's in the console. Unsure if this is a Cisco bug, iOS bug, or what. I am on WLC 8.5.161.0 which I believe to be the TAC recommended build and I believe the consensus here is to stick to this ...
Assignment Required is selected, clients must obtain an IP address via DHCP. Any client with a static IP address is not allowed on the network. The DHCP Required option in WLAN settings allows you to force clients to do a DHCP address. request/renew every time they associate to the WLAN before they are allowed to send or receive other.
WLAN 上で、WLAN に割り当てられたインターフェイスの DHCP サーバ アドレスを上書きする DHCP サーバを定義する場合、[DHCP Server Override] チェックボックスをオンにして、[DHCP Server IP Addr] テキスト ボックスに目的の DHCP サーバの IP アドレスを入力します ...